Bomber Jacket Sizing and Grading: Shoulder and Sleeve Fit

Bomber Jacket Sizing and Grading: Shoulder and Sleeve Fit

Summary

A women's bomber should be graded from the shoulder out: across-shoulder 3/8 inch per size, sleeve length from center-back neck 1/4 to 3/8 inch, bicep 1/4 inch, cuff rib 1/4 inch, bust 2 inches. This pattern-room guide covers armscye geometry, sleeve pitch, rib ratios, petite, tall and plus blocks, the fit session protocol, spec sheet fields and bulk measurement QC, with working grade tables for MOQ 50 pieces per style.

Bomber Jacket Sizing and Grading: Shoulder and Sleeve Fit
Bomber Fit and Grading

Bomber Jacket Sizing and Grading: Shoulder and Sleeve Fit

November 17, 2026 Ginwen Production Team Jacket Manufacturing

A women's bomber jacket should be graded from the shoulder outward, not from the bust. Across-shoulder width grows about 3/8 inch (0.95 cm) per size, sleeve length from center-back neck grows 1/4 to 3/8 inch per size, bicep circumference grows 1/4 inch, and the rib cuff opening grows only 1/4 inch so the elastic still grips the wrist. The bust and hem can move 2 inches per size because the ribbed hem is meant to blouse. Get the shoulder, armscye and sleeve pitch right and the jacket reads as tailored streetwear; get them wrong and every size looks like a borrowed jacket. This guide is the pattern-room version of that rule, written for brand founders and sourcing managers placing a custom bomber jacket program at MOQ 50 pieces per style.

Why Bomber Grading Breaks First at the Shoulder

A bomber is a blouson: the ribbed hem pulls the body in, the body above it drapes out, and the chest never has to be fitted. That single construction choice removes most of the risk from the torso and pushes all of it into the shoulder line. On a fitted blazer, a 1/4 inch error at the shoulder is absorbed by the drape of the front. On a cropped bomber with a 2 inch rib band and a set-in sleeve, the same 1/4 inch error either locks the arm forward or leaves a hollow above the shoulder blade that no amount of steaming will remove.

There is a second reason the shoulder dominates. Women's bombers are usually ordered in shallow size runs of three to five sizes, and the sample is approved on one body. If the grade rule is copied from a men's block, the shoulder grows 1/2 inch per size while the armscye depth grows 1/4 inch. Two sizes up, the sleeve cap no longer has enough room to rotate, and the jacket starts to lift at the front when the wearer raises her arms. The pattern looks correct on paper and fails on the body.

Practical consequence for buyers: specify the sample size explicitly, ask for the grade rule before the first sample is cut, and treat shoulder, bicep and sleeve pitch as approval-critical measurements rather than as part of a general size chart review. If your program includes knit or fleece streetwear alongside woven bombers, the same logic applies with softer tolerances; the bomber versus varsity comparison explains where those tolerances diverge.

3/8 in Typical across-shoulder grade per size
1/4 in Bicep and cuff rib grade per size
3 Fit rounds before bulk approval
5 pcs Per size and color in measurement QC

The Four Control Points That Decide Fit

Every women's bomber program can be controlled with four measurements. Everything else on the spec sheet is secondary, because everything else follows from these four. Define them once, agree the tolerances, and the rest of the size chart becomes arithmetic.

Across Shoulder

Measured seam to seam across the back at the shoulder points, straight across. This number sets the shoulder line and drives the armscye position. Grade 3/8 inch per size on a women's block.

Armscye Depth

From the shoulder point down the back to the underarm line, measured on the pattern rather than the garment. Grade 1/8 to 1/4 inch per size, never more than the shoulder grows.

Sleeve Length

From center-back neck, over the shoulder point, to the cuff edge. This is the only sleeve length that stays stable when the shoulder seam moves. Grade 1/4 to 3/8 inch per size.

Cuff Rib Opening

Relaxed circumference of the rib cuff, not stretched. Grade 1/4 inch per size and check stretched recovery separately. This is where cheap bombers visibly fail.

Why center-back neck matters: Sleeve length measured from the shoulder seam is the most common source of size-run drift. When a drop-shoulder seam moves outward 1 inch between sizes, a seam-based sleeve measurement hides a 1 inch error. Center-back neck cannot drift, so it is the measurement to put in the contract.

Shoulder Width and Slope: The Number Buyers Under-Specify

Across-shoulder width is the first measurement to lock, and the one most often left to the factory's discretion. On a women's bomber it should be specified as a straight-line distance between shoulder points on the back, with the garment flat and the back panel smoothed but not stretched. A size-small women's bomber in a mid-weight nylon shell usually sits between 15 and 15 1/2 inches across the back shoulder; a men's small sits closer to 17 inches. If your buyer profile is a women's brand selling to a European or North American market, accepting the men's block with a smaller chest grade is the single most common reason a first sample photographs badly.

Shoulder slope matters as much as width, and it is invisible on a flat spec sheet. A women's block typically carries a 5/8 to 3/4 inch drop from the neck point to the shoulder point over a 5 inch run, which is slightly steeper than a men's block. Steal two degrees of slope from the pattern and the shoulder seam sits behind the shoulder bone in wear, creating a ridge under the collar and a diagonal pull through the front armhole. The jacket passes a flat-lay inspection and fails a mirror inspection, which is exactly the kind of defect that only surfaces after the bulk order has shipped.

There is a workaround that costs nothing and solves most of this: ask for the shoulder point position, the neck point position and the slope angle as separate spec lines rather than as one width. A factory with a real pattern room can state those numbers in one email. A trading company will send back a size chart with only chest, length and sleeve and will not be able to answer the slope question at all. That single question separates the two supplier types faster than any factory audit.

Sample size convention: Ask the factory to develop on a women's medium with a defined fit model profile, then grade both directions. Developing on small and grading up produces a block with too little armscye depth in the large sizes, and the error compounds toward the top of the run.

Armscye Geometry: Set-In, Raglan and Drop Shoulder

The armscye is where a bomber's silhouette is decided, and the three construction options behave very differently under grading. Choosing between them is a design decision, but each choice carries a specific grading rule that has to be written into the tech pack.

ConstructionShoulder GradeCap EaseFit SignatureGrading Risk
Set-in sleeve3/8 in per size1/2 to 3/4 inClean shoulder line, closest to tailoredHigh if armscye depth lags the shoulder grade
Raglan sleeve1/4 in per size1/4 to 1/2 inSporty, forgiving, strong for knit bodiesLow; diagonal seam hides pitch errors
Drop shoulder3/8 in plus a fixed 1 to 2 in dropNone to 1/4 inOversized streetwear, boxy bodyMedium; sleeve length must be re-measured from center back

Set-in sleeves give the sharpest shoulder and photograph best in lookbooks, but they demand the tightest pattern discipline. Cap ease of 1/2 to 3/4 inch in a woven nylon bomber is enough to let the sleeve hang without a pucker; push past 1 inch and the cap has to be eased in with a seam allowance that shows under a light shell fabric. Under 3/8 inch, the sleeve pulls and the wearer feels the jacket lift when she reaches forward.

Raglan sleeves are the pragmatic choice for first-time programs. The diagonal seam from underarm to neck absorbs small pitch errors, and the grade rule is simpler because there is no shoulder seam to move. The trade-off is visual: raglan reads as casual, so it suits jersey, fleece and softshell bombers better than a satin MA-1 homage.

Drop shoulders are the riskiest under grading because the drop is a fixed design value while the body grows. A 1 1/2 inch drop on a small becomes a 1 1/2 inch drop on an extra large, which on a wider body reads as a much shorter shoulder-to-sleeve proportion. The fix is to reduce the drop by 1/8 inch per size above medium, or to accept the boxier look deliberately and adjust the bicep grade downward so the sleeve does not balloon. Either way, write the rule down. The MA-1, A-2 and B-3 silhouette breakdown shows how much of each style's identity sits in this exact seam.

Sleeve Length and Cuff Position

Sleeve length on a bomber is not a style preference, it is a functional measurement. The rib cuff must sit at the wrist bone so the elastic grips and the hand stays free. Too short and the cuff rides up the forearm when the arm bends; too long and the rib bunches over the hand, which reads as a sizing error to any buyer handling the sample.

Measure from center-back neck over the shoulder point to the cuff edge, with the sleeve laid flat and the rib relaxed. For a women's medium bomber in a standard shell, that number typically lands between 31 1/2 and 32 1/2 inches. Men's equivalents run 34 to 35 inches. If your size chart shows a women's medium at 34 inches, you are almost certainly looking at a men's block that has been re-labelled rather than re-graded, and the cuff will hang past the knuckles.

The cuff itself has two measurements that buyers conflate: relaxed opening and stretched recovery. A 2x2 rib with 3 to 5 percent elastane in a women's medium typically relaxes to about 6 1/2 inches across the flat, giving roughly 13 inches of circumference. That will stretch over a 7 inch hand comfortably and return. If a supplier quotes only a flat width without a recovery figure, ask for a wash test result after five cycles under ISO 6330 at the appropriate care temperature. Rib that loses more than 1/4 inch of relaxed width after five washes will look tired before the first season ends.

Sleeve length tolerance in bulk should be plus or minus 3/8 inch, tighter than the 1/2 inch that many factories default to. The reason is visual: a 1/2 inch split between left and right sleeves on a cropped bomber is immediately visible on a model with arms at rest, and it is the first thing a wholesale buyer checks when opening a carton.

Sleeve Pitch and Rotation: The Defect Nobody Measures

Sleeve pitch is the angle at which the sleeve hangs relative to the body, and it is the most common invisible defect in women's bombers. A correctly pitched sleeve sits slightly forward of the side seam, following the natural rest position of the arm, and rotates freely when the wearer reaches forward. A sleeve set with neutral or backward pitch looks acceptable on a flat lay and pulls across the front of the bicep the moment the jacket is worn.

For a women's block, plan on 5 to 8 degrees of forward pitch at the sleeve cap, with the elbow point shifted forward by 1/4 to 3/8 inch relative to a straight centerline. The practical test is a reach test: with the jacket on and zipped, the wearer raises both arms to shoulder height. The hem should lift no more than 1 1/2 inches, and the front armhole should show no more than a light diagonal drag. Anything sharper means the armscye is too shallow or the pitch is wrong.

Pitch errors are almost never corrected at the fit session because the fit model is usually standing still with arms down. Add an explicit movement protocol to every fitting: arms forward, arms overhead, hands behind the back, seated with elbows on a table. Four positions, two minutes, and half of all pattern rework gets caught before it reaches bulk. This is the part of a sampling round that separates a technical factory from an assembly shop, and it costs nothing but attention.

Do not fix pitch by adding width. The instinct when a sleeve pulls is to widen the bicep. That adds fabric without changing the hang, so the sleeve still drags and now also looks baggy. Fix the pitch angle and the armscye depth first, then re-check bicep circumference.

Grading Increments by Size

The table below is a working women's bomber grade for a three-to-five-size run in a woven shell with rib collar, rib cuffs and rib hem. It is deliberately not a copy of a men's rule set: shoulder and sleeve grow in smaller steps than bust, and the cuff rib is nearly static. Use it as a starting point for discussion with the pattern room rather than as a universal standard, because shell weight, lining and interlining all shift the numbers slightly.

MeasurementXSSMLXLGrade Step
Bust, 1 in below armhole33 in35 in37 in40 in44 in2 in, then 3 to 4 in at XL
Across shoulder, seam to seam15 in15 1/2 in16 in16 3/4 in17 1/2 in3/8 to 1/2 in
Sleeve from center-back neck31 in31 1/2 in32 in32 3/4 in33 1/2 in1/4 to 3/8 in
Bicep, 2 in below armhole11 1/2 in12 in12 3/4 in13 1/2 in14 1/2 in1/4 to 1/2 in
Cuff rib, relaxed flat6 in6 1/4 in6 1/2 in6 3/4 in7 in1/4 in
Front length from high point shoulder21 in21 1/2 in22 in22 1/2 in23 in1/2 in
Hem rib, relaxed flat14 1/2 in15 1/2 in16 1/2 in18 in19 3/4 in1 to 1 3/4 in

Two things in that table deserve comment. First, the hem rib grades much faster than the cuff rib. That is intentional: the hem has to clear the hips, so it follows the body, while the cuff has to grip a wrist that barely changes in circumference across the run. Factories that grade both ribs at the same step produce bombers whose cuffs are loose on smalls and tight on larges, which is the exact opposite of what customers expect.

Second, the jump from large to extra large in the bust is larger than the earlier steps for most Western women's ranges. If your market is predominantly US or UK, plan a 3 inch step there and validate it on a fit model in the XL size rather than extrapolating from the medium. Extrapolated XL samples are a recurring source of returns, and the cost of cutting one extra sample is trivial next to a season of size-related complaints.

Petite, Tall and Plus Ranges Are Separate Blocks

A single graded run cannot serve petite and tall customers, and pretending otherwise is the most expensive mistake in women's outerwear. Petite sizing is not a shorter hem; it is a shorter torso with a raised armscye, a shallower neck drop and a shorter sleeve, all adjusted proportionally. Tall sizing is not a longer hem either; it is a longer torso with a lower armscye and a sleeve that stays at the wrist bone.

  • Petite: shorten body length 1 1/2 to 2 inches, raise armscye depth 1/2 inch, shorten sleeve from center-back neck 1 to 1 1/2 inches, keep shoulder width within 1/4 inch of the main block.
  • Tall: add 1 1/2 to 2 inches to body length, lower armscye 1/4 inch, add 1 to 1 1/2 inches to sleeve, keep the cuff rib unchanged.
  • Plus: rebuild the block rather than grading up. Add a bust cup adjustment, deepen the armscye, increase the bicep independently of the bust, and add a center-front length adjustment so the rib hem sits level.

Plus sizing is where most grading shortcuts become visible. Grading a B-cup block up four sizes produces a jacket that strains across the bust and gapes at the front hem, because the bust projection did not grow with the circumference. A proper full bust adjustment adds length and width through the front panel only, leaving the back and the shoulder seam undisturbed. Ask any supplier whether they cut a separate plus block or grade the base block up; the answer tells you whether they have a pattern room or only a cutting table.

If your range includes school, team or club programs, the same separation logic applies to youth sizing, and the grade steps shrink further. The youth varsity sizing guide covers the equivalent rules for that customer group.

Collar and Hem Rib Ratios

Rib is where a bomber gets its shape, and rib proportion is a grading decision that buyers usually leave unmentioned until the sample arrives. Three ratios control the look: collar height, cuff height and hem height. On a classic MA-1 interpretation in women's sizing, a collar around 2 1/4 inches tall, a cuff around 2 1/2 inches and a hem around 2 inches gives a balanced proportion on a cropped body. Lengthen the hem rib past 3 inches and the jacket reads as a varsity; shorten the collar below 1 3/4 inches and it reads as a track jacket.

The rib width should stay constant across the size run even when the length changes. This seems counterintuitive, because a larger customer often prefers deeper rib for coverage, but consistent rib height is what makes a size run look like one product family in a lookbook. If a buyer wants deeper rib on larger sizes, the change should be 1/4 inch maximum, and the pattern must compensate by shortening the body panel by the same amount so the total garment length stays on grade.

Rib Heights

  • Collar: 2 to 2 1/2 in
  • Cuff: 2 1/4 to 2 3/4 in
  • Hem: 1 3/4 to 2 1/4 in
  • Constant across sizes, 1/4 in max variance

Rib Quality Checks

  • Elastane content 3 to 5 percent
  • Recovery within 1/4 in after 5 washes
  • Join seam placed at side or center back
  • No grin-through at full stretch

Rib tension is the hidden variable. Cutting rib shorter than its relaxed length and stretching it to fit creates the gathered, elastic look that defines a bomber, but the amount of stretch has to be consistent. If the hem rib is cut 10 percent shorter than the body opening on one style and 20 percent shorter on the next, the two jackets will feel like different products in the hand. Specify the stretch percentage, not just the finished measurement, and require the factory to record the cut length on the pattern card.

Bust, Waist and Hem Sweep: How a Bomber Should Not Fit

A bomber is not supposed to fit at the waist. The rib hem defines the narrowest point, and everything above it should fall in a controlled blouse. That means the waist measurement on the spec sheet is largely decorative, and the number that actually matters is the difference between the chest circumference and the hem rib circumference. Too little difference and the jacket looks like a box; too much and the blousing reads as a sizing error.

For a women's medium in a mid-weight shell, a chest-to-hem-rib difference of 4 to 6 inches relaxed produces the classic bloused silhouette. Under 3 inches the jacket sits flat and looks like a windbreaker; over 8 inches it balloons and the front hem lifts away from the body when the wearer moves. The grade should hold that difference roughly constant, allowing it to widen slightly toward the larger sizes where more fabric is needed for the hip.

Front length from high point shoulder is the measurement to watch next. At 22 inches on a women's medium, a bomber sits at the high hip, which suits most streetwear programs. At 24 inches it becomes a boyfriend shape and needs a different hem width to look intentional. Shorten it to 20 inches and the jacket starts to compete with a cropped puffer, so the rib hem has to be narrower to avoid a flare. Whatever length you choose, grade it in 1/2 inch steps and state the intended landing point on the body in the tech pack, because pattern makers work from landing points, not from numbers alone.

Shell weight affects fit more than most buyers expect. A 70 denier nylon blouses differently from a 210 denier twill at the same measurement. If you switch shell fabric after the fit is approved, re-check the hem drop and the sleeve pitch. The bomber fabric guide covers how shell choice changes drape and hand.

The Fit Session Protocol

Fit sessions decide whether a bomber program runs on schedule. A structured three-round sequence, run with a defined model and a written comment sheet, removes most of the back-and-forth that stretches sampling from two weeks to six.

1

Round One: Block and Balance

Proto sample in house fabric. Check shoulder width, armscye depth, sleeve pitch and body balance. Do not discuss trim or color at this stage.

2

Round Two: Fit and Movement

Fit sample in final shell. Run the four-position movement test, confirm cuff landing at the wrist bone, adjust hem blouse and rib tension.

3

Round Three: Size Set

Sewn sample in the smallest and largest sizes. Verify the grade holds the shoulder, sleeve and cuff relationships. Sign off the measurement sheet.

4

Pre-Production

Approved sample sealed, spec sheet frozen, measurement tolerances issued to the QC team before cutting begins.

Typical sampling window: 7 to 14 days per round, with bulk production running 25 to 40 days after approval.

A written comment sheet matters as much as the fitting itself. Verbal comments recorded in a chat thread get reinterpreted by the pattern maker, and the second sample often fixes the wrong problem. Use one sheet per round with a column for the measurement, the target, the actual, the tolerance and the decision. That single document becomes the audit trail if a bulk shipment arrives out of spec.

Spec Sheet and Tech Pack Handover

The measurement sheet is only half of what the factory needs. A usable bomber tech pack carries the grade rule, the tolerances, the landing points, the rib specification and the fit model profile on the same page set. Without the grade rule, the pattern room invents one. Without the fit model profile, the sample is developed against whoever is available in the office that week.

Spec Sheet Must Include

  • Size range and sample size
  • Across shoulder, seam to seam
  • Sleeve from center-back neck
  • Bicep and cuff rib, relaxed
  • Front and back length from HPS
  • Hem rib, relaxed and stretched

Fit Model Profile

  • Height and bust, waist, hip
  • Shoulder width and arm length
  • Dress size in target market
  • Body shape note where relevant
  • Photo of sample on model
  • Recorded movement test result

Construction Details

  • Armscye type and cap ease
  • Sleeve pitch angle
  • Rib stretch percentage
  • Interlining and wadding weight
  • Zipper type and length
  • Seam allowance by seam

Tolerances to Agree

  • Body measures plus or minus 1/4 in
  • Sleeve length plus or minus 3/8 in
  • Rib measures plus or minus 1/8 in
  • No left-right split over 1/4 in
  • Measurement method photographed
  • Points of measure numbered

Two details in that list cause most disputes. First, the points of measure. If the factory measures the chest at the underarm and your QC team measures it 1 inch below, both teams are right and the shipment is still rejected. Number every point and photograph the tape position on the approved sample. Second, the measuring method for knit rib. Rib must be measured relaxed, without tension, on a flat surface, after a 24 hour rest. Measure it straight off the machine and it will read short by 1/4 to 1/2 inch.

For brands moving from a first sample to a repeat order, the tech pack also needs a change log. When a fit correction is approved in round two, record which measurement changed and by how much. Six months later, when a new pattern maker opens the file, the log is the only thing that prevents the original error from being reintroduced. The tech pack to bulk order workflow covers the document handover in more detail.

Bulk Measurement QC: What to Check and How Many

Measurement QC on a bomber should be a sampling exercise with fixed rules, not a spot check performed on whichever carton is open. The practical standard for a program at 50 to 500 pieces per style is five garments per size per color, measured on the same points of measure used at fit approval, with results recorded against tolerance.

CheckSample SizeToleranceAction if Failed
Across shoulder5 pcs per size and colorPlus or minus 1/4 inRe-measure batch, recut if systematic
Sleeve length, center back5 pcs per size and colorPlus or minus 3/8 inSort and re-trim cuff where possible
Cuff rib relaxed10 pcs per size and colorPlus or minus 1/8 inHold shipment, review rib lot
Hem rib relaxed10 pcs per size and colorPlus or minus 1/4 inHold shipment, review rib lot
Front length from HPS5 pcs per size and colorPlus or minus 1/4 inRecut hem, recheck grade
Sleeve pitch, visual100 percent of cartonsNo visible drag at restRe-press, escalate if recurring

The sleeve pitch line in that table is deliberately a visual 100 percent check rather than a measurement. Pitch is a three dimensional property and cannot be verified with a tape on a flat garment, so the check happens on a form or a person, one garment per carton as a minimum. If a carton fails, expand to every garment in that carton before releasing it.

Record the results, not just the pass or fail. A measurement log that shows drift across a production run, sleeve length creeping 1/8 inch longer every 100 pieces, is far more useful than a final inspection report that says the shipment passed. Drift tells you the cutting or the rib lot changed, and it lets you intervene before the last carton is packed.

Six Grading Failures and Their Fixes

  1. Shoulder grows faster than the armscye. The jacket lifts at the front when arms rise. Fix by holding armscye depth to within 1/8 inch of the shoulder grade, then re-cut the sleeve cap.
  2. Bicep graded with the bust. Larger sizes look inflated through the upper arm. Fix by grading bicep independently at 1/4 to 1/2 inch per size regardless of bust steps.
  3. Cuff rib graded like the hem. Cuffs end up loose on smalls and tight on larges. Fix by holding cuff growth to 1/4 inch per size and re-specifying rib cut length.
  4. Sleeve length measured from the shoulder seam. Drop-shoulder styles drift by an inch across the run. Fix by converting every sleeve spec to center-back neck.
  5. Neutral sleeve pitch. Drag appears across the front bicep in wear. Fix by adding 5 to 8 degrees of forward pitch and re-testing with arms forward.
  6. Plus sizes graded from a B-cup block. Bust strains and the front hem gapes. Fix by cutting a separate plus block with a proper bust adjustment.
Do not accept a size chart as proof of grading. A size chart lists numbers; a grade rule explains how those numbers were derived and where the control points sit. Ask for the grade rule. A supplier who can send it within a day has a pattern room; one who cannot is assembling garments from someone else's block. Both can produce a jacket, but only one can hold a size run together across repeat orders.

Frequently Asked Questions

How should a women's bomber jacket be graded for fit?

Grade from the shoulder outward. Across-shoulder width grows about 3/8 inch per size, sleeve length from center-back neck grows 1/4 to 3/8 inch, bicep grows 1/4 inch, and the cuff rib grows only 1/4 inch so it still grips the wrist. Bust can move 2 inches per size because the rib hem is designed to blouse. Keep armscye depth within 1/8 inch of the shoulder grade so the sleeve cap still rotates.

What is a good shoulder width for a women's medium bomber?

Around 16 inches seam to seam across the back, with a shoulder slope of roughly 5/8 to 3/4 inch from neck point to shoulder point. A men's medium usually measures 17 to 17 1/2 inches at the same point, so a women's pattern should not be a scaled men's block.

Where should a bomber cuff sit on the wrist?

At the wrist bone, so the rib grips without bunching over the hand. Measure sleeve length from center-back neck to cuff edge and expect 31 1/2 to 32 1/2 inches on a women's medium in a standard shell. Bulk tolerance should be plus or minus 3/8 inch.

Can one size run cover petite and plus customers?

No. Petite needs a raised armscye and a shorter torso, not just a shorter hem. Plus needs a rebuilt block with a bust adjustment and a deeper armscye. Grading a base block up or down produces measurable fit failures at both ends of the range.

How many fit rounds does a custom bomber program need?

Three is the working standard: block and balance, fit and movement, then a size set in the smallest and largest sizes. At Ginwen, sampling runs 7 to 14 days per round and bulk production 25 to 40 days after approval, with MOQ 50 pieces per style and sample fees of 50 to 200 US dollars that are deductible from the bulk order.

What should I send to get an accurate fit quotation?

Send the size range, your sample size, the target market, a reference garment with its measurements, the shell and lining you intend to use, and any artwork or trim specification. With those five items a pattern room can quote grading and sampling without a second round of questions. You can submit your requirements directly and our team will respond with a specification review.

Bomber sizing is not a size chart exercise. It is a shoulder and sleeve problem with a body attached, and the numbers that decide whether a jacket photographs well are the ones buyers usually leave to the factory: shoulder width and slope, armscye depth, sleeve pitch, sleeve length from center-back neck, and rib tension at the cuff. Specify those five, ask for the grade rule in writing, and run a movement test at every fitting.

For brands building a women's bomber range, the difference between a block that holds across sizes and one that collapses at the ends shows up in returns, not in samples. If you want a second opinion on a size chart, a grade rule or a fit comment sheet, contact our production team and we will review it against the measurements we use in our own pattern room. You can also browse the women's jacket range, read the women's bomber manufacturing guide, or compare notes on women's varsity fit and sizing where the same grade logic applies to a heavier body.